Faulkner County 2.0 earthquake

Preliminary Arkansas Earthquake Report Magnitude 2.0 Md

Seismologists indicate the size of an earthquake in units of magnitude. There are many different ways that magnitude is measured from seismograms because each method only works over a limited range of magnitudes and with different types of seismometers. Some methods are based on body waves (which travel deep within the structure of the earth), some based on surface waves (which primarily travel along the uppermost layers of the earth), and some based on completely different methodologies. However, all of the methods are designed to agree well over the range of magnitudes where they are reliable.

Preliminary magnitudes based on incomplete but available data are sometimes estimated and reported. For example, the Tsunami Centers will calculate a preliminary magnitude and location for an event as soon as sufficient data is available to make an estimate. In this case, time is of the essence in order to broadcast a warning if tsunami waves are likely to be generated by the event. Such preliminary magnitudes, which may be off by one-half magnitude unit or more, are sufficient for the purpose at hand, and are superseded by more exact estimates of magnitude as more data become available.

Earthquake magnitude is a logarithmic measure of earthquake size. In simple terms, this means that at the same distance from the earthquake, the shaking will be 10 times as large during a magnitude 5 earthquake as during a magnitude 4 earthquake. The total amount of energy released by the earthquake, however, goes up by a factor of 32.

Date-Time 14 Jan 2012 03:41:10 UTC

13 Jan 2012 21:41:10 near epicenter

13 Jan 2012 21:41:10 standard time in your timezone

The Uinted States Geological Survey indicates the date and time when the earthquake initiates rupture, which is known as the "origin" time. Note that large earthquakes can continue rupturing for many 10's of seconds. We provide time in  UTC (Coordinated Universal Time). Seismologists use UTC to avoid confusion caused by local time zones and daylight savings time. On the individual event text pages, times are also provided in local US timezones.

Location 35.310N 92.312W

An earthquake begins to rupture at a hypocenter which is defined by a position on the surface of the earth (epicenter) and a depth below this point (focal depth). We provide the coordinates of the epicenter in units of latitude and longitude. The latitude is the number of degrees north (N) or south (S) of the equator and varies from 0 at the equator to 90 at the poles. The longitude is the number of degrees east (E) or west (W) of the prime meridian which runs through Greenwich, England. The longitude varies from 0 at Greenwich to 180 and the E or W shows the direction from Greenwich. Coordinates are given in the WGS84 reference frame. The position uncertainty of the hypocenter location varies from about 100 m horizontally and 300 meters vertically for the best located events, those in the middle of densely spaced seismograph networks, to 10s of kilometers for global events in many parts of the world.

Depth 4 km

The depth where the earthquake begins to rupture. This depth may be relative to mean sea-level or the average elevation of the seismic stations which provided arrival-time data for the earthquake location. The choice of reference depth is dependent on the method used to locate the earthquake. Sometimes when depth is poorly constrained by available seismic data, the location program will set the depth at a fixed value. For example, 33 km is often used as a default depth for earthquakes determined to be shallow, but whose depth is not satisfactorily determined by the data, whereas default depths of 5 or 10 km are often used in mid-continental areas and on mid-ocean ridges since earthquakes in these areas are usually shallower than 33 km.

Distances 3 km (2 miles) SE (127 degrees) of Guy, AR

10 km (6 miles) E (94 degrees) of Twin Groves, AR

11 km (7 miles) NE (38 degrees) of Greenbrier, AR

64 km (40 miles) N (2 degrees) of Little Rock, AR

412 km (256 miles) SSW (207 degrees) of St. Louis, MO

The United States Geological Survey provides distances and directions from nearby geographical reference points to the earthquake. The reference points are towns, cities, and major geographic features. The USGS realizes that these distances are uncertain both because of the errors inherent in locating earthquake (typically one or more kilometers) and because of the impossibility of describing the location of a city by a single longitude-latitude entry in a table. For places in the US, rather than rounding off distances to, say, the nearest 10 kilometers, we chose to trust the user's common sense in interpreting the accuracy of these distances. For places outside the US, distances are rounded depending on the location uncertainty. If the computed location is close to an operating quarry which is known to use explosives in its operations, we indicate that the event may be a quarry explosion. We try to always provide at least one widely recognized reference point in the list on the event page, even if the earthquake occurs in a remote location.

Location Uncertainty Horizontal: 0.6 km; Vertical 0.6 km

The horizontal and vertical uncertainties in an event's location are based on values Ehro and Erzz described below. We assign an "unknown" value if the contributing seismic network does not supply the necessary information to generate uncertainty estimates. The position uncertainty of the hypocenter location varies from about 100 m horizontally and 300 meters vertically for the best located events, those in the middle of densely spaced seismograph networks, to 10s of kilometers for global events in many parts of the world.

Parameters Nph = 22; Dmin = 3.0 km; Rmss = 0.20 seconds; Gp = 57° M-type = Md; Version = A
 
These parameters provide information on the reliability of the earthquake location. Zero values usually indicate that the contributing seismic network did not supply the information. Nst Number of seismic stations which reported P- and S-arrival times for this earthquake. This number may be larger than Nph if arrival times are rejected because the distance to a seismic station exceeds the maximum allowable distance or because the arrival-time observation is inconsistent with the solution.
 
Nph Number of P and S arrival-time observations used to compute the hypocenter location. Increased numbers of arrival-time observations generally result in improved earthquake locations.

Dmin Horizontal distance from the epicenter to the nearest station (in km). In general, the smaller this number, the more reliable is the calculated depth of the earthquake.

Rmss The root-mean-square (RMS) travel time residual, in sec, using all weights. This parameter provides a measure of the fit of the observed arrival times to the predicted arrival times for this location. Smaller numbers reflect a better fit of the data. The value is dependent on the accuracy of the velocity model used to compute the earthquake location, the quality weights assigned to the arrival time data, and the procedure used to locate the earthquake.

Erho The horizontal location error, in km, defined as the length of the largest projection of the three principal errors on a horizontal plane. The principal errors are the major axes of the error ellipsoid, and are mutually perpendicular. Erho thus approximates the major axis of the epicenter's error ellipse.

Erzz The depth error, in km, defined as the largest projection of the three principal errors on a vertical line. See Erho

Gp The largest azimuthal gap between azimuthally adjacent stations (in degrees). In general, the smaller this number, the more reliable is the calculated horizontal position of the earthquake. Earthquake locations in which the azimuthal gap exceeds 180 degrees typically have large Erho and Erzz values.

M-type Magnitude type, discussed at greater length above under Magnitude

Version Computers automatically update the WWW pages as more reliable information about the earthquake is computed, particularly in the first 10 minutes following the earthquake. The highest version number is always considered authoritative.

Event ID NM 011401b

The event id is a combination of a 2-letter Seisimic Network Code and a number assigned by the contributing seismic network.